JD Engineering (Northern) Ltd

MOT Lanes

We are currently deleloping a new page for MOT equipment.

It will be going live very soon, at which point we will be offering new and pre-owned MOT equipment.

Please do not hesitate to contact sales for information prior to the launch of new pages

Precision Point Laser Tracking Gauges - 325.00 GBP

These Precision Point Laser 2-wheel tracking gauges are ideal for small workshops. They are fast and easy to use with laser technology which makes this simple wheel alignment system accurate. These laser wheel alignment gauges are around 2 years old and are in very good condition. They work on practically all cars and light commercial vehicles with rim diameters from 200mm to 600mm.

These guages are powered by 2 x AA batteries and can easily be self-calibrated making them cheap to run. A conversion calculator from degress to millimeters or inches is mounted on the tracking gauges.

COLLECTION & DELIVERY
Collection is free during normal office hours from our purpose built warehouse. If you require delivery please contact us for a competitive quote. Please read our Collection & Delivery section for important information about our delivery service.

OTHER OPTIONS
Some items may have additional options. Please select any you require from the Product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.

HPC SM8 Screw Compressor - 1,500.00 GBP

This HPC SM8 Plusair tank-mounted screw compressor is in immaculate condition and has been serviced by HPC agents since new.

The unit has done 14000 hours, less than half of which on load. The compressor has been fully serviced and tested in our specialsed workshop. The compressor has a normal working pressure of 10 bar (normal workshop pressure) and its output air volume is 30cfm (cubic feet minute) which means it is capable of running a small to medium sized workshop or bodyshop. The compresor has a intergrated 170 litre receiver ideal for space saving. It requires a 16amp 3-phase power supply to operate.

This screw compressor is ready for delivery or collection from our Hull based warehouse.

INSTALLATION
We recommend compressors are professionally installed. We provide a professional installation service if required. Please select your installation option from the drop down menu below. Please read our Installation section for important information about our professional installation service.

OTHER OPTIONS
Some items may have additional options. Please select any you require from the Product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.

HH Intertech 2.5 tonne baseless lift/ramp - 750.00 GBP

HH Intertech HH227 2 post baseless lift.

Picture to follow shortly

Finished in white, this baseless two post lift was manufactured in 1997

In good condition, this lift/ramp was removed from a main dealership by our engineers. It will go through our workshop to be checked/tested prior to palletising for dispatch.

INSTALLATION
We recommend vehicle lifts are professionally installed. We provide a professional installation service if required. Please select your installation option from the drop down menu below. Please read our Installation section for important information about our professional installation service.

OTHER OPTIONS
Some items may have additional options. Please select any you require from the product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.

Tecalemit Mk5 twintec 2.5 tonne 2 post Lift / Ramp - 720.00 GBP

This Tecalemit 2.5 tonne, two post vehicle lift was recently removed from a leading dealership's workshop. It was covered by a full maintenance contract whilst installed at the dealership and was in perfect working order when removed by our own engineers.

The lift has blue paintwork. It will go through our workshop to be service/checked and tested prior to collection or delivery. These early to mid 90's 2 post lifts have were always been popular with mechanics and garages alike for there easy, trouble free use.

The picture is for reference only. The lift is the same model and type as the one palletised in this photo, finished in blue paintwork.

A 3 phase power supply is required to run this based screw lift.

A fitting service is available if required and details can be found below or contact us for a quote.

COLLECTION & DELIVERY
Collection is free during normal office hours from our purpose built warehouse. If you require delivery please contact us for a competitive quote. Please read our Collection & Delivery section for important information about our delivery service.

INSTALLATION
We recommend 2 post vehicle lifts are professionally installed. We provide a professional installation service if required. Please select your installation option from the drop down menu below. Please read our Installation section for important information about our professional installation service.

OTHER OPTIONS
Some items may have additional options. Please select any you require from the Product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.

Bradbury 2603 2.5 tonne 2 post lift/ramp - 700.00 GBP

2 post Bradbury 2603 2.5 tonne vehicle lift/ramp

Manufactured in 1997 this baseless Bradbury hydraulic two post ramp was un-installed by our engineers in good working order.

HH Intertech 3 tonne 2 post lift/ramp - 825.00 GBP

HH Inertech 2 post baseless ramp with 3 tonne capacity.

This lift was manufactured in 1997, it has an overhead gantry, leaving a level floor between the baseplates of each post.

In very good condition, this lift was removed from a main dealerships workshop by our own engineers. The lift will go through our own workshop to be service/checked prior to being palletised in readiness for dispatch.

OTHER OPTIONS
Some items may have additional options. Please select any you require from the Product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.

Corghi EM7040 Wheel Balancer - 550.00 GBP

The Corghi EM7040 wheel balancer has automatic start when the protective guard is lowered.

This balancer requires a single phase power supply.

In good condition with a simple-user friendly keyboard for data inpit and programme selection

OTHER OPTIONS
Some items may have additional options. Please select any you require from the product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.

John Bean Balco 9450 Wheel Balancer - 595.00 GBP

John Bean Balco 9450 motorised digital wheel balancer. This semi-automatic machine is a space saving wheel balancer which was manufactured in 2004 and is in good condition. The machine only requires a single phase, 13 amp, 3-pin plug power supply. This popular machine is easy to use with a dual digital display and semi-automatic features.

This Balco machine has the Following features:

Automatic start by lowering the wheel guard
Spindle lock, via foot brake pedal
Semi-automatic distance/offset entry
Steel and alloy wheel adapters
Automatic spindle brake after the measuring run

Photo coming soon.

Need a tyre machine? Click here.

OTHER OPTIONS
Some items may have additional options. Please select any you require from the product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.

Wilmat Elevator Truck - 665.00 GBP

Wilmat

Manual push, battery powered elevator truck.

In good working order

Red paintwork is looking a liitle worse for wear but can be painted pre collection for £95

We have been using the elevator lift at our premises but it will go through our workshop to be tested/checked before dispatch.

This item can be collected from our warehouse in Hull or if you provide us with your postcode we can give you a quote for delivery to your premises

INSTALLATION
We recommend two post lifts are professionally installed. We provide a professional installation service if required. Please select your installation option from the drop down menu below. Please read our Installation section for important information about our professional installation service.

OTHER OPTIONS
Some items may have additional options. Please select any you require from the product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.

OTHER OPTIONS
Some items may have additional options. Please select any you require from the product Options drop down menu below.

V.A.T.
All prices shown are subject to V.A.T. which is calculated at the checkout once you have logged in.